Pages

Thursday, 8 June 2017

First Artilley Castings

The blog has been very quiet as of late as the moulds are taking a long time - and I have to confess to my recent wargaming currently being in other scales and periods. Anyway, enough of the excuses, I finally received some test moulds over the weekend, and as it was good casting weather I gave them a go.

I was told in advance that it would be difficult to cast the wheels (it always is), however I did manage to get some good castings, by a combination of:
  • Using the expensive Model Metal.
  • Venting the wheels on every spoke.
  • Applying talc between every pour - and then ensuring the vents were clear.
  • The minimum clamping force I could get way with.
  • Giving the moulds a good tap when full.
  • Good luck/weather.
They do take a bit of cleaning up - but not too bad.

One of the reasons the mould production has been further delayed as Chris (the sculptor) decided that the spokes needed thickening up a bit to make casting easier (I have the unmodified version).

I have cast a gun to carry each of the four barrels, and they look pretty good, although compromises have to be made to allow all the barrel sizes to fit between the carriage cheeks.

Austrian 6pdr



The wheels measure about 33mm tall, and the crew are about 44mm to top of head. As the Austrian wheels were 51" high, that makes the crew 5' 8" tall, perhaps a bit on the tall size but not far off. (As is always the case with shots like this, the fact that the figures are on a thick base makes them look taller.)


Also, the moulds will not contain an elevating wedge, so I decided to make one by cutting a triangle off the corner of a 1.5mm thick MDF base using a razor saw.

The axles are round (I know that is wrong), which allows the wheel track to be adjusted. I have made the Austrian track 43" - which looks narrow - but distinctive.

The crew are painted in sleeveless waistcoats, not quite correct, the most noticeable differences being that there should be two rows of buttons on the front of the waistcoat, and the gunners amongst the crew (about half) should have boots rather than gaiters.

However overall I think it looks fine, which is what we were aiming for.

Russian Unicorn


The barrel on this is quite short, so I modified the position of the cross member below the back of the barrel, and added an elevating screw. However I am sure it will look fine with the barrel just glued on with no elevating mechanism.


The wheels are set further apart which makes it look much more distinct than it would be if just the barrel was changed.


The crew are the same as for the Austrians, this time painted with the waistcoats long sleeved. I could not resist adding a bombardier in the distinctive helmet.


Other Options


There are to other barrels in the moulds, which will make up a Prussian light 12pdr, for which I have just added the wedge.


I have not painted up a crew for the Prussian gun, as the ones I have cast have gone to Richard Hattersley for painting to use on the packaging.


And an Austrian 7pdr howitzer, for which I again added a wedge, and relocated the support cross member a bit lower and further forward  (and also set the wheels closer together).



And finally for a size comparison the new gun alongside the Karoliner 3pdr - which I might try with the new wheels?


I don't think these are far off production - but how many times have I said that?

As always comments are very welcome - particularly if they are positive....

................bring on the cavalry?

Extra photos to answer comments......


A close up of the wheel as cast with the vent holes.  In the production moulds the spokes will be heavier to simplify casting - I have not seen the new wheel yet and will cast a couple when I get  a mould.

Rahway asked about the vent on the Austrian guns - you can just about see the vent on the shot of the howitzer, however to put his mind at ease here is a close up on the 6pdr (the barrels will clean up better than this without too much work).


Rahway asked about the height of the figures. I have to confess that initially I thought that they are way too big when compared with the infantry.


They are probably a little bit larger, however the thing is that the gunners are bolt upright, whereas everything else has a very distinct lean, and the figures are similar distance heel to top of head.

The base IS too big, and that will be corrected in the production mould.



9 comments:

  1. Not sure what I'll do with a bunch more guns, might have to modify my rules to encourage myself to field more gun models!

    The wheels should be particularly useful. Might even use them to retrofit some of my Scruby 19thC guns.

    ReplyDelete
    Replies
    1. Ross
      I have inserted a photo of the wheel I have - it needs a lot of venting. The production mould will have heavier spokes.
      Steve

      Delete
  2. Thank you Steve. The wheels look good.

    I think it is understood that compromises are needed when trying to use one carriage for many purposes.
    Two questions:
    Are the gunners much larger than the infantry?
    The angled vent does not show on the Austrian gun due to the angle of the photo. Does it look right to you?

    ReplyDelete
    Replies
    1. Rahway

      The gunners may be a little bit larger, but this is exaggerated by the fact that they are upright and the infantry leaning - I have added some photos.

      I have added a close up of the vent, it looks fine to me.

      Steve

      Delete
  3. The new guns look great!

    Best Regards,

    Stokes

    ReplyDelete
  4. Very good shot of the detail on the Austrian gun. It looks good.

    Since the gunners and the infantry will usually have some diastase between them the size difference will not be readily apparent, particularly if they are Russians deployed near the "straight-up" marching Russian infantry.

    ReplyDelete
  5. Thank you , as always, for those photos !!

    models are great and very usefull for a lot of things !!!

    best regards
    paco

    ReplyDelete
  6. Just a quick question and only a little unrelated, I'd like to make an English army do you think any of the current Prince August figures would be suitable if painted correctly.

    ReplyDelete
    Replies
    1. Sorry for delay in response, as PA have been pretty quiet I have not had anything to post recently.

      With regards the British, they had quite distinct lapels, cuffs and baggage see Kronoskaf page:

      http://www.kronoskaf.com/syw/index.php?title=1st_Foot

      It really depends how close you want to get, the Prussians might be closest as they have no collars, and a sword scabbard.

      If you are after early period with the waist belts on the outside perhaps the French with turned back coats.

      I think the intention is to do some, but it will be years away.

      You could probably use the shirtsleeve artillery which is just about to go into production, and hopefully cavalry not too far away.

      Get back if you need more help.

      Steve

      Delete